Mechanical Engineering Science

Mechanical Analysis for Two-layered Ultrahigh Pressure Apparatus with Interlayer Pressure

ZHAOMengjun, ZHUPengchen, LIUZan, KANGChao

Abstract


To improve the bearing pressure capacity of ultrahigh pressure apparatus, the internal autofrettaged cylinder with interlayer pressure (ACCIP) is introduced, and the analytical model for the ACCIP structure and its derivation are presented as well. Calculation showed that the ACCIP method enhance bearing pressure of the apparatus obviously; optimization results revealed that under the working pressure pw=1.07σs and different radius ratios, the ACCIP method can keep the apparatus in deformed-elastically state; And when the pw=1.07σs, the minimum radius ratio was approximate 3.29, in this case, no yielding happened. The above results demonstrate that the ACCIP method is a promising technique to improve the bearing pressure of ultrahigh pressure apparatus, and the analytical model for the ACCIP method is also reasonable. In addition, the minimum radius ratio ro/ri under randomly specified workload can be Fig.d out by the analytical model proposed in this work.

Keywords


mechanical analysis; ultrahigh pressure; interlayer pressure; analytical mode

Full Text:

PDF

References


Wang, Z., Yuan, S., Hu, L., Wang, Z., and He, Z. (2007), Fundamentals of elasticity OF and plasticity, (2nd Edition). Harbin: Harbin institute of technology press.

Miraje, A. A and Patil, S. A. (2011) “Minimization of material volume of three layer compound cylinder having same materials subjected to internal pressure”, International Journal of Engineering, Science and Technology, 3(8), 26-40. http://doi.org/10.4314/ijest.v3i8.3.

Yuan, G. and Liu, H. (2012), “An analytical solution of residual stresses for shink-fit two-layer cylinders after autofrettage based on actual material behavior”, Journal of Pressure Vessel Technology, 134(6), 061209. http://doi.org/10.1115/1.4006121.

Zhu, Q., Zhao J., Zhang, C., Zhang, D. and Wang, S. (2015), “Elastic-brittle-plastic unified solutions of limit internal pressure for double-layered combined thick-walled cylinder”, Engineering Mechanics, 32 (9), 68-75. http://doi.org/10.6052/j.issn.1000-4750.2013.07.0627.

Shufen, R. , N. Mahanta , and U. S. Dixit . "Development of a Thermal Autofrettage Setup to Generate Compressive Residual Stresses on the Surfaces of a Cylinder." Journal of Pressure Vessel Technology 141.5(2019). DOI: 10.1115/1.4044119.

Zhu, R. and Yang, J. (1998), “Autofrettage of thick cylinders”, International Journal of Pressure Vessels & Pining, 75(6), 443-446. http://doi.org/10.1016/S0308-0161(98)00030-1.

Lee, E. Y., Lee, Y. S., Yang, Q. M., Kim, J. H., Cha, K. U. and Hong, S. K. (2009), “Autofrettage Process analysis of a compound cylinder based on the elastic-perfectly plastic and strain hardening stress-stain curve”, Journal of Mechanical Science and Technology, 23(12), 3153-3160. http://doi.org/10.1007/s12206-009-1009-9.

Yang, Q. M., Lee, E. Y., Lee, Y. S., Kim, J. H., Cha, K. U. and Hong, S. K. (2009), “A residual stress analysis program using a Matlab GUI on an autofrettaged compound cylinder”, Journal of Mechanical Science and Technology, 23(11), 2913-2920. http://doi.org/10.1007/s12206-009-0820-7.

Maleki, M., Farrahi, G. H., Jahromi, B. H. and Hosseinian, E. (2010), “Residual stress analysis of autofrettaged thick-walled spherical pressure vessel”, International Journal of Pressure Vessels & Piping, 87(7), 396-401. http://doi.org/10.1016/j.ijpvp.2010.04.002.

Zhu, R., Zhu G. and Mao, A. (2010), “Mechanical analysis of autofrettaged high pressure apparatus”, Journal of Theoretical and Applied Mechanics, 55(1), 17-27. http://doi.org/10.15632/jtam-pl.55.1.17.

Shim, W. S., Kim, J. H., Lee, Y. S., Cha, K. U. and Hong, S. K. (2010), “A study on Hydraulic Autofrettage of Thick-Walled Cylinders Incorporating Bauschinger Effect”, Experimental Mechanics, 50(5), 621-626. http://doi.org/10.1007/s11340-009-9255-4.

Alexandrov, S., et al. "Description of Residual Stresses in Autofrettaged Open-Ended Cylinders Made of High-Strength Steel." Materials 13.13(2020):2940.DOI: 10.3390/ma13132940.

Wahi, N., Ayob, A. and Elbasheer, M. K. (2011), “Effect of Optimum Autofrettage on Pressure Limits of Thick-Walled Cylinder”, International Journal of Environmental Science and Development, 2(4), 329-333. http://doi.org/10.7763/IJESD.2011.V2.146.

Hu, Z. and Puttagunta, S. (2012), “Computer modeling of internal pressure autofrettage process of a thick-walled cylinder with the bauschinger effect”, American Transactions on Engineering & Applied Sciences, 1(2), 143-161.

Zhu, R. L., Zhu, G. L. and Tang, F. (2012), “Analysis on autofrettage of cylinders”, Chinese Journal of Mechanical Engineering, 25(3), 615-623. http://doi.org/10.3901/CJME.2012.03.615.

Li, G. , et al. "Research on Autofrettage Mechanism in Ultra-High Pressure Thick-walled Vessel." Journal of Physics: Conference Series 1802.2(2021):022001 (6pp). http://doi.org/10.1088/1742-6596/1802/2/022001.

Miraje, A. A. and Patil, S. A. (2011), “Minimization of material volume of three layer compound cylinder having same materials subjected to internal pressure”, Internal Journal of Engineering, Science and Technology, 3 (8), 26-40.http://doi.org/10.4314/ijest.v3i8.3.

Boresi, A. P., Sidebottom, O. M., Seely, F. B. and Smith, J. O. (1978), Advanced Mechanics of Materials, (3rd Edition.), John Wiley & Sons, New YorK: John Wiley & Sons.




DOI: https://doi.org/10.33142/mes.v3i1.4330

Refbacks

  • There are currently no refbacks.


Copyright (c) 2021 Mengjun ZHAO, Pengchen ZHU, Zan LIU, Chao KANG

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.