Study on polyurethane-based porous materials and their adsorption properties
Abstract
The flexible superhydrophobic thermoplastic polyurethane(TPU) porous material was prepared by heat-induced phase separation method with two cooling steps. The influence of the preparation process on the microstructure of the material was discussed in depth. The microstructure, hydrophobicity and specific surface area of porous TPU materials were analyzed in detail. The surface wettability, separation selectivity, saturated adsorption capacity and adsorption rate, mechanical properties, environmental adaptability and cyclic properties of porous TPU materials were studied.The results show that the TPU-8% porous monolithic material prepared by heat-induced phase separation method shows good performance when the polymer concentration is 8%, the phase separation temperature is 0°C, the phase separation time is 30min, and the mixing solvent ratio is 9:1.
Keywords
Full Text:
PDFReferences
Ge J, Zhao H Y, Zhu H W, et al. Advanced sorbents for oil-spill
cleanup: Recent advances and future perspectives [J].
Advance Materials, 2016(28): 10459-10490.
Wang X L, Pan Y M, Liu X H, et al. Facile fabrication of
superhydrophobic and eco-friendly polylactic acid foam for
oil-water separation via skin-peeling [J]. ACS Applied
Materials & Interfaces, 2019(11): 14362-14367.
Wang S, Peng X W, Zhong L X, et al. An ultralight, elastic,
cost-effective, and highly recyclable superabsorbent from
microfibrillated cellulose fibers for oil spillage cleanup [J].
Journal of Materials Chemistry A, 2015(3): 8772-8781.
Kujawinski E B, Kido Soule M C, Valentine D L, et al. Fate of
dispersants associated with the deepwater horizon oil spill
[J].Environmental Science Technology, 2011(45): 1298-1306.
Broje V, Keller A A. Improved mechanical oil spill recovery
using an optimized geometry for the skimmer surface [J].
Environmental Science Technology, 2006(40): 7914-7918.
Aurell J, Gullett B K. Aerostat sampling of PCDD/PCDF
emissions from the gulf oil spill in situ burns [J].
Environmental Science Technology, 2010(44): 9431-9437.
Bayat A, Aghamiri S F, Moheb A, et al. Oil spill cleanup from
Bi H C, Xie X, Yin K B, et al. Spongy graphene as a highly
efficient and recyclable sorbent for oils and organic solvents
[J]. Advanced Functional Materials, 2012(22): 4421-4425.
Azizian, S. Kinetic Models of Sorption: a Theoretical
Analysis.[J]. Colloid Interface Sci. 2004(276): 47−52.
Wang H, Wang E, Liu Z, Gao D, Yuan R, Sun L, Zhu Y.A novel
carbon nanotubes reinforced superhydrophobic and
superoleophilic polyurethane sponge for selective oil/water
separation through a chemical fabrication. [J]. Mater. Chem.
(3): 266−273.
Wu Y, Xue S, Yang H, Zhang H, Zhang T,Gou
S.Polymerization-Induced Phase Separation for the
Fabrication of Magnetic Sponges for Oil Spill Reclamation.
Chem. Eng. [J]. 2017(328): 639−644.
Cao N, Yang B, Barras A, et al. Polyurethane sponge
functionalized with superhydrophobic nanodiamond
particles for efficient oil/water separation [J]. Chemical
Engineering Journal, 2017(370): 319-325.
He Y Q, Liu Y, Wu T, et al. An environmentally friendly
method for the fabrication of reduced graphene oxide foam
with a super oil absorption capacity [J]. Journal of
Hazardous Materials, 2013(260): 796-805.
DOI: https://doi.org/10.33142/rams.v4i1.8458
Refbacks
- There are currently no refbacks.
Copyright (c) 2023 Jiajia LI, Jiahui ZHU, Jialin GU, Zhenhao ZHOU, Qi SUN, Guangcan GUO, Yibin ZHOU, Shujun CHEN, Xinggang SHAN, Gangqiang WANG
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.